![]() ![]() You are thinking of Plus Adding, or not taking out, Noise. So I do Noise Reduction in Post Processing and I try to stop the camera from doing any noise reduction. Visibility of dense areas such as the heart and mediastinum is greatly improved.įujifilm’s SmartSwitch technology enables automatic x-ray detection. I have my Fuji camera set to the lowest, Negative, Minus Sign, NR allowed on the cameras. ![]() This enhancement achieves 1.7 times the DQE of previous models, with as little as 0.03mrad dose. Noise reduction circuitry improves sensitivity in high absorption regionsĪ unique, Fujifilm innovation in noise reduction circuitry maximizes signal strength to improve image quality in high absorption areas. This design significantly suppresses scattering and attenuation of X-ray signals, improving efficiency to produce sharper images at lower doses compared to traditional designs. Patented ISS capture technology promotes high sensitivityįujifilm’s proprietary Irradiated Side Sampling (ISS) positions its capture electronics (TFTs) at the irradiation side, in contrast to traditional detectors. Virtual Grid intelligent image processing replaces the use of a grid to enhance contrast and improve clarity while reducing dose as much as 50% compared to exams performed with a grid. Intelligent Virtual Grid image processing for situations where grid use can be challenging The resulting first-up images have outstanding detail and greater window and leveling capability in PACS. Squealing issue is completely gone and the behavior of my lens is back to normal! I've had confirmation from a couple of other people that this works for them too.Īll the usual caveats apply here of course, YMMV, use at your own risk, void your warranty etc.Refined Dynamic Visualization image processing produces exceptional imagesįDR D-EVO GL utilizes the latest Fujifilm digital image processing technology, including Dynamic Visualization, which optimizes image display based on recognition of contrast levels throughout the entire exposure field. I loaded my patched "3.23 in 3.24 clothing" version onto the SD card, the update ran successfully and upon restarting and doing the firmware check the lens now says version 3.23 (as the actual firmware version number is contained in the code, the header is simply to tell the installer which version it's looking at before installing) MD5 checksum for the patched firmware: 9f79d44b34c6910a035a9e547edbea3e You can quickly check the integrity of the patched firmware file by dragging and dropping it here to make sure the patch was applied correctly: Fujifilm positions its thin-film transistors (TFT) at the top of the capture layer, reading image data where it is sharpest and strongest, resulting in exceptional detail and image quality, even at lower doses. No other changes to the firmware file occurred) Fujifilm’s patented Irradiated Side Sampling (ISS) technology increases sharpness and DQE by reducing light scatter and blur. (I confirmed afterwards with a hex editor that the only change between the original 3.23 and the patched "3.24" version was a single byte near the beginning of the file (23 became 24). Go back to the top and click "Download patched firmware" ![]() Make sure the only option selected is "Increment version by 1"Ĭlick "Compile patched firmware" button down the bottom I used the brilliant FujiHack firmware patcher to increment the version number by 1 so that the 3.23 firmware would appear to the camera as 3.24, and thus allow it to re-install over the faulty 3.24 firmware.Ĭlick "Choose file" and select the 3.23 firmware downloaded from the Wayback Machine So the above 3.23 version above is useless as the camera will refuse to downgrade to a lower version. If it's the same or higher than the current lens version it will install, if it's lower it won't install it. All FDR D-EVO II models utilize the same user-swappable battery type. Extended battery life standby time of up to 48 hrs. Fits every neonatal isolette detector tray. When the camera loads the firmware from the SD card, it looks at the file header for the version number. Exceptional imaging with improved dose efficiency. I had looked at a few posts about the firmware before updating but somehow missed all of the posts regarding the issues people were having! It doesn't seem to be super widespread but I've personally seen posts from at least 20 people affected by this issue.īy sheer luck, a single copy of the previous 3.23 firmware was archived on the Wayback Machine so I could compare it to the current 3.24 firmware I had downloaded and installed. I updated my XF 18-55 (made in Japan) a few days ago and it started doing the horrible squealy noise when zoomed between 35-55mm. ![]()
0 Comments
Leave a Reply. |